黄色片黄色片黄色片亚洲黄色片,欧美日韩不卡高清在线,国产亚洲情侣久久精品,久久中文字幕av第二页

適用范圍]:

適用于棉、滌棉、梭織棉面料等的仿拔染印花。

(不受染料或非染料的面料限制。 甚至對含滌綸成分較高的混合棉料進行仿拔白印花。)

[性 質]:

外 觀: 乳白色糊狀物

主成分: 丙烯酸聚氨酯共聚物、精細鈦白

離子性: 陰離子

[保 質 期]:

室溫5-35℃,避免暴曬 或 冷凍, 貯存1年。

[特 征]:

穩定性良好，精細光滑，紋理清晰，接近拔印效果，透氣性好，能在深色布上進行彩色印花的高遮蓋水漿,色澤飽滿、遮蓋力較強、牢度好、手感較軟、無異味、無腐蝕性,環保指數達國際環�？椢镆�求。

[一般配比]:

仿拔染水漿(拔白漿) 100-97%

固色劑/交聯劑 0-3% (酌情少放)

100克

印花工藝：(Mesh網布80-100目) 印花1次1-2刀 → 烘干、干燥 → 可用隧道烘箱烘焙 或 壓燙。

[注意事項]:

先將布鋪平,跑道烘車將布片的水份蒸發后,再印花效果更佳。

1) 先把漿料上下攪拌均勻。

2) 根據面料的(棉、滌)成分,選擇合適的固色劑或交聯劑(注意固色劑的時效性) ,避免使用陽離子助劑。

3) 以日本印花慣例:調漿后 印刷前,先把漿料過濾一次,使?jié){體更細膩,色澤更均勻,手感更流暢,效果更佳。(推薦)

4）干透后再進行烘箱熱處理,可以有效增加牢度。印花24小時后,方可測試?yán)味取?若：要手感好,建議少放固色劑/交聯劑,烘焙溫度盡可能控制在80℃以內(高溫會導致手感偏硬)。剛烘干的印花面,手感偏硬,隨著時間的推移(隔天)會變?nèi)彳洝?/span>

-------------------------------------------------------------------

上述資料,僅供參考,不作法律依據。按“國際化工慣例”：每次使用前,客戶必須試驗確認后,方可批量投入使用,否則后果與我方無關

Other detailed information

Scope :cotton, mercerized cotton, woven cotton

[Characters]:

Appearance :milky white viscous body

Main component: acrylic polyurethane copolymer, fine titanium dioxide

Ionic: anion

[shelf life] :

At room temperature5-35℃,avoid exposure or freeze,the shelf life is one year.

[Features ]:

Good stability,fine and smooth,clear textures,close to discharge effect,good permeability,which is a high covering slurry that can print on the dark fabric.

Saturated color,super coverage,good fastness,soft hand feel,odorless, the environmental indicator reaches international textile's requirements

[Ratio]:

Discharge like water paste(discharge like white) 100-97%

Fixing agent/cross linker 0-3%(or less)

100g

Printing technology:(mesh screen 80-100)print one time scrape once-twice →drying→hot pressure

[Notes] :

Pull down fabric first and evaporate water,then printing effect is better.

1)stir paste evenly and mildly in first time

2)According the component of fabric,choosing proper fixing agent or cross linker(pay attention to timely),avoid to use cationic auxiliaries.

3)According to Japanese printing regulars: after adjusting paste,before printing,filter the paste for one time,make the paste more stained,the gloss is more evenly and mildly,good hand feel and better effect.

4)After drying,making heat pressure by dryer to increase fastness. If: need good hand feel,advice to use litter fixing agent/cross linker,temperature of baking should be controlled within 80℃（high temperature will lead to hard hand feel.）the surface of printing,hand feel is prefer to be hard,with time goes by, it becomes softer.